boards: add intive GmbH 2C2L-USB

CMakeLists.txt

@@ -279,6 +279,7 @@ set(TGTF407_LIST
 	"STM32F4_DevBoard"
 )
 set(TGTG0B1_LIST
+	"2C2L_USB"
 	"CONVERTDEVICE_xCANFD"
 	"budgetcan"
 	"candleLightFD"

include/config.h

@@ -312,6 +312,18 @@ THE SOFTWARE.
 
 /*************** STM32G0B1 ***************/
 
+#elif defined(BOARD_2C2L_USB)
+	#define USBD_PRODUCT_STRING_FS	 "intive 2C2L-USB gs_usb"
+	#define USBD_MANUFACTURER_STRING "intive"
+	#define DFU_INTERFACE_STRING_FS	 "intive 2C2L-USB firmware upgrade interface"
+
+	#define HSE_OSC_SPEED			 8000000
+	#define TIM2_CLOCK_SPEED		 64000000
+
+	#define CAN_CLOCK_SPEED			 40000000
+	#define NUM_CAN_CHANNEL			 2
+	#define CONFIG_CANFD			 1
+
 #elif defined(BOARD_CONVERTDEVICE_xCANFD)
 	#define USBD_PRODUCT_STRING_FS	 "ConvertDevice xCANFD"
 	#define USBD_MANUFACTURER_STRING "ConvertDevice"

src/boards/g0b1-2C2L_USB.c

@@ -0,0 +1,174 @@
+/*
+
+The MIT License (MIT)
+
+Copyright (c) 2023 Pengutronix,
+              Marc Kleine-Budde <[email protected]>
+
+Copyright (c) 2024 intive GmbH,
+              Hubert Denkmair <[email protected]>
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+
+*/
+
+#include "board.h"
+#include "config.h"
+#include "device.h"
+#include "gpio.h"
+#include "usbd_gs_can.h"
+
+/*
+   LED_RX   PB14
+   LEX_TX   PB13
+   UART_TX  PB6
+   UART_RX  PB7
+   USB_P    PA12
+   USB_N    PA11
+   CAN1_RX  PD0
+   CAN1_TX  PD1
+   CAN1_S   PD2
+   CAN2_RX  PB0
+   CAN2_TX  PB1
+   CAN2_S   PB9
+*/
+
+#define LEDRX_GPIO_Port	  GPIOB
+#define LEDRX_Pin		  GPIO_PIN_14
+#define LEDRX_Mode		  GPIO_MODE_OUTPUT_PP
+#define LEDRX_Active_High 1
+
+#define LEDTX_GPIO_Port	  GPIOB
+#define LEDTX_Pin		  GPIO_PIN_13
+#define LEDTX_Mode		  GPIO_MODE_OUTPUT_PP
+#define LEDTX_Active_High 1
+
+static void intive2c2lusb_setup(USBD_GS_CAN_HandleTypeDef *hcan)
+{
+	GPIO_InitTypeDef GPIO_InitStruct;
+
+	UNUSED(hcan);
+
+	__HAL_RCC_GPIOB_CLK_ENABLE();
+	__HAL_RCC_GPIOD_CLK_ENABLE();
+
+	/* LEDs */
+	HAL_GPIO_WritePin(LEDRX_GPIO_Port, LEDRX_Pin, GPIO_INIT_STATE(LEDRX_Active_High));
+	GPIO_InitStruct.Pin = LEDRX_Pin;
+	GPIO_InitStruct.Mode = LEDRX_Mode;
+	GPIO_InitStruct.Pull = GPIO_NOPULL;
+	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+	HAL_GPIO_Init(LEDRX_GPIO_Port, &GPIO_InitStruct);
+
+	HAL_GPIO_WritePin(LEDTX_GPIO_Port, LEDTX_Pin, GPIO_INIT_STATE(LEDTX_Active_High));
+	GPIO_InitStruct.Pin = LEDTX_Pin;
+	GPIO_InitStruct.Mode = LEDTX_Mode;
+	GPIO_InitStruct.Pull = GPIO_NOPULL;
+	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+	HAL_GPIO_Init(LEDTX_GPIO_Port, &GPIO_InitStruct);
+
+	/* Setup transceiver silent pin */
+	HAL_GPIO_WritePin(GPIOD, GPIO_PIN_2, GPIO_PIN_RESET);
+	GPIO_InitStruct.Pin = GPIO_PIN_2;
+	GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+	GPIO_InitStruct.Pull = GPIO_NOPULL;
+	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+	HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
+
+	HAL_GPIO_WritePin(GPIOB, GPIO_PIN_9, GPIO_PIN_RESET);
+	GPIO_InitStruct.Pin = GPIO_PIN_9;
+	GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+	GPIO_InitStruct.Pull = GPIO_NOPULL;
+	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+	HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+	/* FDCAN */
+
+	RCC_PeriphCLKInitTypeDef PeriphClkInit = {
+		.PeriphClockSelection = RCC_PERIPHCLK_FDCAN,
+		.FdcanClockSelection = RCC_FDCANCLKSOURCE_PLL,
+	};
+
+	HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+	__HAL_RCC_FDCAN_CLK_ENABLE();
+
+	/* FDCAN1_RX, FDCAN1_TX */
+	GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1;
+	GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+	GPIO_InitStruct.Pull = GPIO_NOPULL;
+	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+	GPIO_InitStruct.Alternate = GPIO_AF3_FDCAN1;
+	HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
+
+	/* FDCAN2_RX, FDCAN2_TX */
+	GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1;
+	GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+	GPIO_InitStruct.Pull = GPIO_NOPULL;
+	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+	GPIO_InitStruct.Alternate = GPIO_AF3_FDCAN2;
+	HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+}
+
+static void intive2c2lusb_phy_power_set(can_data_t *channel, bool enable)
+{
+	UNUSED(channel);
+	UNUSED(enable);
+}
+
+static void intive2c2lusb_termination_set(can_data_t *channel, enum gs_can_termination_state enable)
+{
+	UNUSED(channel);
+	UNUSED(enable);
+}
+
+const struct BoardConfig config = {
+	.setup = intive2c2lusb_setup,
+	.phy_power_set = intive2c2lusb_phy_power_set,
+	.termination_set = intive2c2lusb_termination_set,
+	.channels[0] = {
+		.interface = FDCAN1,
+		.leds = {
+			[LED_RX] = {
+				.port = LEDRX_GPIO_Port,
+				.pin = LEDRX_Pin,
+				.active_high = LEDRX_Active_High,
+			},
+			[LED_TX] = {
+				.port = LEDTX_GPIO_Port,
+				.pin = LEDTX_Pin,
+				.active_high = LEDTX_Active_High,
+			},
+		},
+	},
+	.channels[1] = {
+		.interface = FDCAN2,
+		.leds = {
+			[LED_RX] = {
+				.port = LEDRX_GPIO_Port,
+				.pin = LEDRX_Pin,
+				.active_high = LEDRX_Active_High,
+			},
+			[LED_TX] = {
+				.port = LEDTX_GPIO_Port,
+				.pin = LEDTX_Pin,
+				.active_high = LEDTX_Active_High,
+			},
+		},
+	},
+};