This repository contains the files needed to run the RISC-V rocket chip on various Zynq FPGA boards (Zybo, Zedboard, ZC706) with Vivado 2014.2. Efforts have been made to not only automate the process of generating files for these boards, but to also reduce duplication as well as the size of this repo. Prebuilt images are available in git submodules, and they are only shallowly cloned if requested.
###How to use this README
This README contains 3 major sets of instructions:
-
Quick Instructions: This is the simplest way to get started - you'll download the relevant prebuilt images for your board and learn how to run binaries on the RISC-V Rocket Core. These instructions require only that you have a compatible board - neither Vivado nor the RISC-V Toolchain are necessary.
-
Pushing Your Rocket Modifications to the FPGA: These instructions walk through what we believe is the common case - a user wanting to utilize a custom-generated Rocket Core.
-
Building Everything from Scratch: Here, we discuss how to build the full stack from scratch. It is unlikely that you'll need to use these instructions, unless you are intending to make changes to the configuration of the Zynq ARM Core or
u-boot.
Finally, the bottom of the README contains a set of Appendices, which document some common operations that we believe are useful or provides more depth on commands described elsewhere in the documentation.
To guide you through the rest of the documentation, we have provide both a Table of Contents and an Overview.
- Overview of System Stack
- 1 - Quick Instructions
- 2 - Pushing Your Rocket Modifications to the FPGA
- 3 - Building Everything from Scratch
- Appendices
- Acknowledgements
Our system will allow you to run a RISC-V binary on a rocket core instantiated on a supported Zynq FPGA. This section will outline the stack of all of the parts involved and by proxy, outline the rest of the documentation. Going top-down from the RISC-V binary to the development system:
Target Application (RISC-V binary) will run on top of whatever kernel the rocket chip is running. Compiled by riscv-gcc or riscv-llvm.
RISC-V Kernel (proxy kernel or RISC-V Linux) runs on top of the rocket chip. The proxy kernel is extremely lightweight and designed to be used with a single binary linked against Newlib while RISC-V Linux is appropriate for everything else.
Rocket Chip (rocket core with L1 instruction and data caches) is instantiated on the FPGA. Many of its structures will typically map to various hard blocks including BRAMs and DSP slices. It communicates to the host ARM core on the Zynq via AXI.
Front-end Server (riscv-fesvr) runs on the host ARM core and provides an interface to the rocket chip running on the FPGA (connected via AXI).
Zynq ARM Core (actually dual Cortex A9) runs Linux and simplifies interfacing with the FPGA.
FPGA Board (Zybo, Zedboard, or ZC706) contains the Zynq FPGA and several I/O devices. At power on, the contents of the SD card are used to configure the FPGA and boot Linux on the ARM core.
External Communication (TTY over serial on USB or telnet/ssh over ethernet) allows the development system to communicate with the FPGA board.
Development System (PC with SD card reader) generates the images to configure the FPGA.
Using prebuilt images, run hello world and/or linux on rocket
First, enter into the directory for your board (current options are zybo, zedboard, and zc706). From there, run the following to download all of the necessary images:
$ make fetch-images
If you'd also like to try riscv-linux on rocket, run the following:
$ make fetch-riscv-linux
Next, insert the SD card on the development system and copy over the images:
$ make load-sd SD=path_to_mounted_sdcard
Finally, eject the SD card, insert it into the board and power the board on. Connect to the board with an ethernet cable (password is root) and run hello world:
$ ssh [email protected]
root@zynq:~# ./fesvr-zynq pk hello
hello!
Awesome! You can now run RISC-V binaries on Rocket. If you'd like to boot linux on the Rocket core, see Booting Up and Interacting with the RISC-V Rocket Core.
Requires: Vivado 2014.2 and its settings64.sh sourced
If you don't already have a copy of the rocket chip, get a new one:
$ git clone [email protected]:ucb-bar/rocket-chip.git
Move fpga-zynq (this repo) to be within rocket-chip:
$ mv path_to_fpga-zynq/fpga-zynq rocket-chip/
Note: If you like, you can have fpga-zynq and rocket-chip have any relative position as long as you change the symlink fpga-zynq/rocket-chip to point to rocket-chip (by default it is .., its parent directory).
Enter into the directory for your board (current options are zybo, zedboard, and zc706). Generate a Vivado project for the board:
$ make project
The verilog for the rocket chip is generated by Chisel and thus is not intended to be edited by humans. To change the rocket chip, you should modify its chisel code and regenerate the verilog. For information on changing rocket chip, consult its documentation.
Requires: JVM that can run Scala
After making changes within rocket-chip, to run the rocket chip generator and copy the newly generated verilog back into the board's source, run:
$ make rocket
The rocket chip will be configured by the configuration named CONFIG in the board's Makefile. If you wish to use a different configuration, you will need to change your vivado project to be aware of the new verilog source or regenerate the project because configuration names are included in the filename (e.g. Top.DefaultConfig.v).
Once you have changed the design, you will need to generate a new bitstream and that will need to be packaged in boot.bin. boot.bin also contains the binaries needed for startup (FSBL.elf and u-boot.elf) but these can be reused. From within the board's directory (zybo in this example), to repack boot.bin:
$ make fpga-images-zybo/boot.bin
If you have modified the verilog for your project but not generated a new bitstream, make should generate a new bitstream automatically. To use the new boot.bin, copy it to the SD card, insert the SD card into the board, and power on the board.
This section describes how to build the entire project from scratch. Most likely, you will not need to perform all of these steps, however we keep them here for reference. Various other sections of this README may selectively refer to these sections. This section assumes that you've just pulled this repository and have sourced the settings file for Vivado 2014.2.
For ease of exposition, we will be describing all of the commands assuming that we are working with the zybo. Replacing references to the zybo with zedboard or zc706 will allow you to use these instructions for those boards.
From here on, $REPO will refer to the location of the fpga-zynq repository.
First, we need to generate a Vivado project from the source files that are present in a particular board's directory.
$ cd $REPO/zybo
$ make project
Next, let's open up the project in the Vivado GUI:
$ make vivado
# OR
$ cd zybo_rocketchip
$ vivado zybo_rocketchip.xpr
If you wish to make any modifications to the project, you may now do so. Once you've finished, let's move on:
Inside Vivado, select Open Block Design followed by system.bd in the dropdown. This will open a block diagram for the Zynq PS Configuration and is necessary for correct FSBL generation.
Next, select Generate Bitstream. Vivado will now step through the usual Synthesis/Implementation steps. Upon completion, if you're interested in only the bitstream, you can stop here; the file you want is in:
$REPO/zybo/zybo_rocketchip/zybo_rocketchip.runs/impl_1/rocketchip_wrapper.bit
Otherwise, let's continue on to select Open Implemented Design. This is again necessary to properly export the description of our Hardware for the Xilinx SDK to use.
At this point, select File -> Export -> Export Hardware. This will create the following directory:
$REPO/zybo/zybo_rocketchip/zybo_rocketchip.sdk
This directory contains a variety of files that provide information about the hardware to the SDK. Let's continue on to building the FSBL.
This step assumes that you have just generated the bitstream. Inside the Vivado GUI, select "Launch SDK". This will open up the Xilinx SDK preconfigured with the description of our hardware. In order to generate the FSBL, do the following:
-
Select File -> New -> Application Project
-
In the new window, type "FSBL" as the Project name, and ensure that the rest of the properties are correctly set (disregarding the greyed out Location field):
-
Select Next, at which point you should be given a set of options. Select Zynq FSBL and Finish.
-
The SDK will proceed to automatically compile the FSBL. You can see the progress in the Console.
-
Once the build is finished, we need to build u-boot before returning to the SDK in order to create our BOOT.bin.
Returning to the command line, do the following from the directory corresponding to your board:
$ make arm-uboot
This target performs a variety of commands. It will first pull the u-boot source from the Xilinx repositories (see the submodule in $REPO/common/u-boot-xlnx), patch it with the necessary files found in $REPO/zybo/soft_config/, compile u-boot, and place the resulting u-boot.elf file in $REPO/zybo/soft_build/u-boot.elf.
At this point, we have built up all of the necessary components to create our boot.bin file. Returning to the Xilinx SDK, select Xilinx Tools -> Create Zynq Boot Image.
First, you should fill in the Output BIF file path with $REPO/zybo/deliver_output. If this directory has not already been created, you may go ahead and create it (this is where we will place all of the items that we will ultimately transfer to the SD card). See the below for a sample path. Performing this step will also fill in the Output path field, which specifies the location of the BOOT.bin file that we desire.
Next, we will add the individual files that make up BOOT.bin. Order is important, so follow these steps exactly:
- Select Add and in the window that opens, click Browse and specify the following location:
$REPO/zybo/zybo_rocketchip/zybo_rocketchip.sdk/FSBL/Debug/FSBL.elf
Once you have done so select the dropdown next to Partition type and select bootloader. You must perform this step after selecting the path, else the SDK will change it back to datafile, and your BOOT.bin will not work.
At the conclusion of this step, the Add partition window will look something like:
Click _OK_to return to the previous window.
- Once more, click Add. In the new Add partition window, click Browse and specify the following location:
$REPO/zybo/zybo_rocketchip/zybo_rocketchip.runs/impl_1/rocketchip_wrapper.bit
Ensure that Partition type is set to datafile and click OK.
- Click Add a final time. Click Browse and this time select our compiled
u-boot.elf:
$REPO/zybo/soft_build/u-boot.elf
Again, ensure that Partition type is set to datafile and click OK.
- At this point, the window should match the following (click the image to zoom in):
Select Create Image. This will produce a BOOT.bin file in the $REPO/zybo/deliver_output directory.
If you make modifications to the project in the future, you can avoid having to perform this step manually and instead may reuse the output.bif file that the SDK generates the first time you use Create Zynq Boot Image. Use the following make target to do so:
$ make deliver_output/boot.bin
As part of our bootstrapping process, we need to boot linux on the ARM core in the Zynq. We can build this copy of linux like so (again assuming that we are in $REPO/zybo):
$ make arm-linux
We additionally need to produce the devicetree.dtb file that linux will use to setup peripherals of the ARM core. We can produce this like so:
$ make arm-dtb
At this point, the $REPO/zybo/deliver_output directory contains the following files:
BOOT.bin- (the filename is case insensitive, you may seeboot.bin). This contains the FSBL, the bitstream with Rocket, and u-boot.uImage- Linux for the ARM PSdevicetree.dtb- Contains information about the ARM core's peripherals for linux.
The only remaining file that we are missing at this point is uramdisk.image.gz, the root filesystem for linux on the ARM Core. You can obtain it like so (it will be placed in $REPO/zybo/deliver_output):
$ make fetch-ramdisk
Now, take the four files in deliver_output/, and place them on the root of the SD card that we will insert into the Zybo. The layout of your SD card should match the following:
SD_ROOT/
|-> boot.bin
|-> devicetree.dtb
|-> uImage
|-> uramdisk.image.gz
At this point, you have performed the necessary steps to run binaries on Rocket. See Section 3.8 for how to do so. If you are interested in running riscv-linux on Rocket, continue on to Section 3.7:
There are two options to obtain riscv-linux:
Note: If you are working with the Zybo, you should not build riscv-linux from source. The Zybo cannot fit an FPU and thus uses a modified version of the kernel that ignores FPU instructions. Software floating point emulation support is planned but not yet available. The binary for this build can be obtained using Method 2 below.
To build riscv-linux for Rocket, follow the instructions here. Upon completing the linked tutorial, you should have two files: vmlinux and root.bin. You should place them on your SD card in a directory called riscv.
Run the following from within $REPO/zybo.
$ make fetch-riscv-linux-deliver
Then, copy the $REPO/zybo/deliver_output/riscv directory to the root of your SD Card.
After performing either of these steps, your SD card layout should match the following:
SD_ROOT/
|-> riscv/
|-> root.bin
|-> vmlinux
|-> boot.bin
|-> devicetree.dtb
|-> uImage
|-> uramdisk.image.gz
First, insert the SD card and follow the instructions in Appendix A to connect to your board. You can login to the board with username root and password root. Once you're at the prompt, you can run a basic hello world program on rocket like so:
root@zynq:~# ./fesvr-zynq pk hello
hello!
If you've downloaded the necessary files to boot riscv-linux, you may now do so. First however, you should mount the SD card using the instructions in Appendix B. Then, to boot riscv-linux, run:
root@zynq:~# ./fesvr-zynq +disk=/sdcard/riscv/root.bin /sdcard/riscv/vmlinux
Once you hit enter, you'll see the linux boot messages scroll by, and you'll be presented with a busybox prompt from riscv-linux running on rocket!
####Serial-USB On the Zybo and Zedboard a single serial-USB cable is needed but on the ZC706 you will also need a USB type A to type B cable (and possibly some drivers). To connect:
$ screen /dev/tty.usbmodem1411 115200,cs8,-parenb,-cstopb
Note: The numbers following tty.usbmodem may vary slightly. On the Zybo,
replace usbmodem with usbserial- and on the ZC706, replace it with
SLAB_USBtoUART.
####Ethernet The board has an IP of 192.168.1.5 and can be accessed by username/password of root/root on telnet and ssh. For example:
$ ssh [email protected]
Note: Make sure your development system ethernet interface is configured to be on the 192.168.1.x subnet. The default configuration intends for the board to be directly attached to the development system (single cable). If you want to place the board on a larger network, we recommend changing the root password to something stronger and changing the IP configuration to mesh well with your network.
###B) Getting Files On & Off the Board
####Copying Files over Ethernet The easiest way to get a file onto the board is to copy it with scp over ethernet:
$ scp file [email protected]:~/
Note: Linux is running out of a RAMdisk, so to make a file available after a reboot, copy it to the SD card or modify the RAMdisk.
You can mount the SD card on the board by:
root@zynq:~# mkdir /sdcard
root@zynq:~# mount /dev/mmcblk0p1 /sdcard
When you are done, don't forget to unmount it:
root@zynq:~# umount /sdcard
####Changing the RAMDisk Requires: u-boot and sudo
The RAMDisk (uramdisk.image.gz) that holds Linux for the ARM cores is a gzipped cpio archive with a u-boot header for the board. To open the RAMdisk:
$ make ramdisk-open
When changing or adding files, be sure to keep track of owners, groups, and permissions. When you are done, to package it back up:
$ make ramdisk-close
A useful application of this is to add your SSH public key to .ssh/authorized_keys so you can have passwordless login to the board.
Note: Since these ramdisk operations use sudo on files, they may not work on a network mounted filesystem. To get around this limitation, it is easiest to just copy it to a local filesystem when modifying the ramdisk.
Requires: Vivado 2014.2 and its settings64.sh sourced
First, enter into the directory for your board (current options are zybo, zedboard, and zc706). To generate a bitstream, you will need a Vivado project. You should only need to generate it once, but the automation this repo provides makes it easy to generate again if you delete the project. To generate a Vivado project from scratch:
$ make project
To generate a bitstream from the command-line:
$ make bitstream
To launch Vivado in GUI mode:
$ make vivado
###D) Changing the Processor's Clockrate
You can change the clockrate for the rocket chip by changing RC_CLK_MULT and RC_CLK_DIVIDE within a board's src/verilog/clocking.vh. After that change, you will need to generate a new bitstream (and boot.bin).
Note: Although rarely needed, it is possible to change the input clockrate to the FPGA by changing it within the block design, src/constrs/base.xdc, and ZYNQ_CLK_PERIOD within src/verilog/clocking.vh. This will also require regenerating FSBL.elf, the bitstream, and of course boot.bin.
###E) Contents of the SD Card The SD card is used by the board to configure the FPGA and boot up the ARM core. All of these files are available within a board's fpga-images submodule, but they can also be built from scratch. Here is a summary of the files and their purposes:
boot.binis generated by the Xilinx SDK and is actually three files. To generate it from scratch, follow the instructions from Section 3 up through Section 3.5 Creating boot.bin. To repack it from existing components, follow Repacking boot.bin.boot.bincontains:- Bitstream (
rocketchip_wrapper.bit) configures the FPGA with the rocket chip design. To build it with the GUI, see Section 3.2 Generating a Bitstream and to build it with the command-line, see: Working with Vivado. - First Stage Bootloader (
FSBL.elf) - This bootloader configures the Zynq processing system based on the block design in the Vivado project. The FSBL will hand-off tou-bootonce the processing system is setup. We build the FSBL using the Xilinx SDK and hardware information exported from Vivado. (see Section 3.3) - u-boot (
u-boot.elf) - This bootloader takes configuration information and prepares the ARM processing system for booting linux. Once configuration is complete,u-bootwill hand-off execution to the ARM linux kernel. We buildu-bootdirectly from the Xilinx u-boot repository, with some configuration modifications to support Rocket. (see Section 3.4)
- Bitstream (
- ARM Linux (
uImage) - This is a copy of linux designed to run on the ARM processing system. From within this linux environment, we will be able to run tools (likefesvr-zedboard) to interact with the RISC-V Rocket Core. We build directly from the Xilinx linux repository, with a custom device tree file to support Rocket. (see Section 3.6) - ARM RAMDisk (
uramdisk.image.gz) - The RAMDisk is mounted by ARM Linux and contains the root filesystem. For obtaining it, see Section 3.6, and for modifying it, see Appendix B. devicetree.dtb- Contains information about the ARM core's peripherals for Linux. (See Section 3.6)riscv/(optional) - This directory is only needed if you intend to run Linux on the rocket chip itself.- RISC-V Linux (
riscv/vmlinux) - This is the kernel binary for Linux on Rocket. If you are using the zybo, you will need to use a special kernel that ignores floating point instructions, since the zybo cannot fit an FPU. Fetching this version is handled automatically by our scripts. (See Section 3.7) - RISC-V RAMDisk (
riscv/root.bin) - The RAMDisk is mounted by RISC-V Linux and contains the root filesystem. (See Section 3.7)
- RISC-V Linux (
The source code for the fesvr-zynq binary is in the riscv-fesvr repo. To build the riscv-fesvr binary for Linux ARM target (to run on Zynq board), type:
$ mkdir build
$ cd build
$ ../configure --host=arm-xilinx-linux-gnueabi
$ make
from the riscv-fesvr/build directory and make sure you have the Xilinx SDK in your PATH. When installing fesvr-zynq, don't forget to copy the library as well (build/libfesvr.so to /usr/local/lib on the board).
In addition to those that contributed to rocket chip, this repository is based on internal repositories contributed by:
- Rimas Avizienis
- Jonathan Bachrach
- Scott Beamer
- Sagar Karandikar
- Andrew Waterman