Running Windows 3.1 in VMware, DOSBox-X, or QEMU, but annoyed by having to grab and ungrab the cursor manually?
Wish you could just move the cursor in and out like a modern OS (one with USB tablet support or VMware Tools drivers), with no Ctrl+Alt(+G) dancing?
Or want to control your cursor at all under the ESXi web UI? (It doesn't do relative input.)
With this driver, now you can. It implements the interface that VMware uses (the backdoor), replacing the existing PS/2 mouse driver.
example.mp4
qemu.mp4
Glad you asked!
Normally, mice work by sending a delta of their movements. You'd have to trap the mouse inside of the guest for this to work; any tracking difference would result in a very hard to control cursor. Being able to send the absolute coordinates would be great, because you can know the exact point when the cursor hits the edge.
However, there wasn't a standard way of doing absolute positioning with PC input devices until the USB tablet standard, and Windows 3.x/DOS massively predate USB, let alone have a USB stack. For those situations, VMware offers absolute positioning through a port I/O interface.
So let's use said interface. What we need to do is threefold for an MVP:
- On initialization, make the cursor absolute (four calls)
- On deinitialization, make the cursor relative (a single call)
- Instead of parsing PS/2 mouse events, ask VMware for mouse events instead
- Well, we should check if we're even using a supported host, but hey...
The challenge is doing this from real or 286 protected mode, because we need to
set the 32-bit extended versions of the registers (i.e. EAX instead of AX).
The toolchain we're using is MASM, since we're keeping this easy and using the
example drivers from the DDK, just modified. This means we can just plop the
.386 directive in a suitable place in the code, and EAX will become
available to use.
One interesting bit with the mouse driver is the SF_ABSOLUTE bit in a Windows
mouse driver. When passed as the flags for the mouse event (in AX), it'll be
an absolute position instead of relative - exactly what we want, without any
trickery! Even better, it takes a range of 0 through FFFFh, as basically a
percentage of where it is on the screen, in BX and CX. This way, you don't
need to know the resolution of the screen when calculating the absolute
position. Turns out this is exactly how VMware sends the coordinates in EBX
and ECX!
The unfortunate difference is in button handling; VMware sends what buttons are currently held, while Windows wants to know when the button goes down and when it comes up. I've implemented a crude solution, but I think it could be done a lot better. Right now, only two buttons are supported, but in theory, we could send a third with a refactor to the driver. (We're also throwing away the wheel event - that could be four and five, considering Windows 3.x predates the wheel entirely.)
One annoying thing about the sample driver is because the fact it supports multiple types of mouse, it uses a tactic of copying the interrupt handler into a specifically sized buffer. This means you can't go over 210 bytes for the interrupt handler right now; this could be alleviated with a major refactor or rewrite. For now, I've excised the normal PS/2 mouse handling in favour of only using the VMware backdoor. I've also had to occasionally be worried about the length of instructions; shaving things off by only using the 16-bit view of a register, for example.
Overall, I'm glad this was surprisingly easy, considering I didn't know x86 assembly before, and I only implemented this in a day - with lots of struggling against MASM and typos.
(Updates: I've cleaned up button handling, and I'm experimenting on the wheel.)
VMware and QEMU are supported. I have tested Workstation and ESXi. I can't test Fusion because my Mac is M1, so oh well.
VMware will need no configuration. QEMU also needs no configuration - the vmmouse automatically gets attached when the backdoor is added. Don't try adding it any command line flags; you're likely to just crash it.
(For QEMU, you can verify things by running info mice and info qtree.)
Make sure you have the Windows 3.1 Device Development Kit installed.
Inspect the values in SETUPENV.BAT and INSTALL.BAT, then run:
setupenv.bat
nmake
If building from source; after building, run INSTALL.BAT. This will overwrite
the stock mouse driver, so make a backup. The INF install is less crumbly, so I
recommend you go for that.
If using binaries, run Windows Setup. Point where the driver and INF file are;
if you're using the floppy, it'll likely be A:. Restart Windows and enjoy.
Serve with garnish.
Note that if you're using the GUI version of Windows Setup, after selecting the VMware mouse driver for the first time, the combo box might go blank. If that's the case, you need to select it again. This doesn't happen from the DOS version of Windows Setup (when setup is run outside of Windows or at install).