Add Samples

Add sample files to configs.

Closes issues #312 and #316

configs/samples/beagle.conf.sample

@@ -0,0 +1,25 @@
+; If you are going to use this channel driver, you MUST enable it in modules.conf
+; enable it in modules.conf
+; change:
+; noload => chan_beagle.so ;                      Beagleboard Radio Interface Channel Driver
+; to:
+; load => chan_beagle.so ;                      Beagleboard Radio Interface Channel Driver
+
+[general]
+
+[1]
+carrierfrom = hwinvert
+ctcssfrom = hwinvert
+invertptt = 0
+duplex = 1
+rxondelay = 0
+eeprom = 0
+
+[2]
+carrierfrom = hwinvert
+ctcssfrom = hwinvert
+invertptt = 0
+duplex = 1
+rxondelay = 0
+eeprom = 0
+

configs/samples/dnsmgr.conf.sample

@@ -0,0 +1,5 @@
+[general]
+enable=yes		    ; enable creation of managed DNS lookups
+			        ; default is 'no'
+refreshinterval=300	; refresh managed DNS lookups every <n> seconds
+                    ; default is 300 (5 minutes)

configs/samples/echolink.conf.sample

@@ -0,0 +1,53 @@
+; If you are going to use this channel driver, you MUST enable it in modules.conf
+; change:
+; noload => chan_echolink.so 		; echolink Channel Driver
+; to:
+; load => chan_echolink 			; echolink Channel Driver
+
+[el0]
+call = INVALID						; Change this!
+pwd = INVALID						; Change this!
+name = YOUR NAME					; Change this!
+qth = INVALID						; Change this!
+email = INVALID						; Change this!
+node = 000000                       ; Change this!
+; Data for EchoLink Status Page
+lat = 0.0							; Latitude in decimal degrees
+lon = 0.0							; Longitude in decimal degrees
+freq = 0.0                          ; not mandatory Frequency in MHz
+tone = 0.0                          ; not mandatory CTCSS Tone (0 for none)
+power = 0							; 0=0W, 1=1W, 2=4W, 3=9W, 4=16W, 5=25W, 6=36W, 7=49W, 8=64W, 9=81W (Power in Watts)
+height = 0							; 0=10 1=20 2=40 3=80 4=160 5=320 6=640 7=1280 8=2560 9=5120 (AMSL in Feet)
+gain = 0							; Gain in db (0-9)
+dir = 0								; 0=omni 1=45deg 2=90deg 3=135deg 4=180deg 5=225deg 6=270deg 7=315deg 8=360deg (Direction)
+
+maxstns = 20						; Max Stations
+
+rtcptimeout = 10					; Max number of missed heartbeats from EL
+recfile = /tmp/echolink_recorded.gsm	;
+astnode = 1999						; Change this!
+context = radio-secure				; Default in code is echolink-in
+
+; Max 4 servers
+server1 = nasouth.echolink.org
+server2 = naeast.echolink.org
+server3 = servers.echolink.org
+server4 = backup.echolink.org
+
+; To deny w6xxx you would add the statement: deny = w6xxx
+; To prohibit computer-based connections you would write: permit = *-*
+; To allow access to only a select group of callsigns: permit = w6abc,w6def,...
+
+; permit							; comma delimited list of callsign, type (-r)
+; deny
+
+
+; Remote text commands thru netcat:
+; o.conip <IPaddress>    (request a connect)
+; o.dconip <IPaddress>   (request a disconnect)
+; o.rec                  (turn on/off recording)
+
+; ipaddr
+; port
+
+#tryinclude custom/echolink.conf

configs/samples/extensions.conf.sample

@@ -0,0 +1,175 @@
+[general]
+
+static = yes       ; These two lines prevent the command-line interface
+writeprotect = yes ; from overwriting the config file. Leave them here.
+
+[globals]
+HOMENPA = 999 ; change this to your Area Code
+NODE = 1999   ; change this to your node number
+
+[default]
+exten => i,1,Hangup
+
+[radio-secure]
+;exten => ${NODE},1,rpt(${EXTEN})
+exten => _XXXX!,1,NoOp(Connect from node: ${CALLERID(num)})
+	same => n,NoOp(Connect to: ${EXTEN})
+	;same => n,NoOp(The IAXPEER is ${IAXPEER(CURRENTCHANNEL)})
+	same => n,NoOp(The Channel IP is ${CHANNEL(peerip)})
+
+	;If channel IP eq localhost go to connect
+	same => n,GotoIf($["${CHANNEL(peerip)}" = "127.0.0.1"]?connect)
+
+	;If allowlist/extension dosen't exist check the denylist
+	same => n,GotoIf($[${DB_KEYCOUNT(allowlist/${EXTEN})} = 0]?denylist) ;goto denylist
+	;If allowlist/extension/callerid exists go to connect
+	same => n,GotoIf(${DB_EXISTS(allowlist/${EXTEN}/${CALLERID(num)})}?connect) ;goto connect
+	same => n,NoOp(${EXTEN} not in allowlist, Hangup)
+	same => n,Hangup
+
+	;If denylist/extension/callerID doesn't exist goto connect
+	same => n(denylist),GotoIf(${DB_EXISTS(denylist/${EXTEN}/${CALLERID(num)})}?:connect) ;don't goto connect
+	same => n,NoOp(${EXTEN} is in denylist, Hangup)
+	same => n,Hangup
+
+	same => n(connect),rpt(${EXTEN})
+	same => n,Hangup
+
+[iaxrpt]
+; Entered from iaxrpt in iax.conf
+; Info: The X option passed to the Rpt application
+; disables the normal security checks.
+; Because incoming connections are validated in iax.conf,
+; and we don't know where the user will be coming from in advance,
+; the X option is required.
+exten => ${NODE},1,rpt(${EXTEN}|X)       ; NODE is the Name field in iaxrpt
+
+[iax-client]                            ; for IAX VoIP clients.
+exten => ${NODE},1,Ringing()
+	same => n,Wait(10)
+	same => n,Answer()
+	same => n,Set(CALLSIGN=${CALLERID(name)})
+	same => n,NoOp(Caller ID name is ${CALLSIGN})
+	same => n,NoOp(Caller ID number is ${CALLERID(number)})
+	same => n,GotoIf(${ISNULL(${CALLSIGN})}?hangit)
+	same => n,Playback(rpt/connected-to&rpt/node)
+	same => n,SayDigits(${NODE})
+	same => n,rpt(${NODE}|P|${CALLSIGN}-P)
+	same => n(hangit),NoOp(No Caller ID Name)
+	same => n,Playback(connection-failed)
+	same => n,Wait(1)
+	same => n,Hangup
+
+; Comment-out the following clause if you want Allstar Autopatch service
+[pstn-out]
+exten => _NXXNXXXXXX,1,playback(ss-noservice)
+	same => n,Congestion
+
+; Un-comment out the following clause if you want Allstar Autopatch service
+;[pstn-out]
+;exten => _NXXNXXXXXX,1,Dial(IAX2/allstar-autopatch/\${EXTEN})
+; same => n,Busy
+
+[invalidnum]
+exten => s,1,Wait(3)
+	same => n,Playback(ss-noservice)
+	same => n,Wait(1)
+	same => n,Hangup
+
+[radio]
+exten => _X11,1,Goto(check_route,${EXTEN},1);
+exten => _NXXXXXX,1,Goto(check_route,1${HOMENPA}${EXTEN},1)
+exten => _1XXXXXXXXXX,1,Goto(check_route,${EXTEN},1)
+exten => _07XX,1,Goto(parkedcalls,${EXTEN:1},1)
+exten => 00,1,Goto(my-ip,s,1)
+
+[check_route]
+exten => _X.,1,Noop(${EXTEN})
+; no 800
+exten => _1800NXXXXXX,2,Goto(invalidnum,s,1)
+exten => _1888NXXXXXX,2,Goto(invalidnum,s,1)
+exten => _1877NXXXXXX,2,Goto(invalidnum,s,1)
+exten => _1866NXXXXXX,2,Goto(invalidnum,s,1)
+exten => _1855NXXXXXX,2,Goto(invalidnum,s,1)
+; no X00 NPA
+exten => _1X00XXXXXXX,2,Goto(invalidnum,s,1)
+; no X11 NPA
+exten => _1X11XXXXXXX,2,Goto(invalidnum,s,1)
+; no X11
+exten => _X11,2,Goto(invalidnum,s,1)
+; no 555 Prefix in any NPA
+exten => _1NXX555XXXX,2,Goto(invalidnum,s,1)
+; no 976 Prefix in any NPA
+exten => _1NXX976XXXX,2,Goto(invalidnum,s,1)
+; no NPA=809
+exten => _1809XXXXXXX,2,Goto(invalidnum,s,1)
+; no NPA=900
+exten => _1900XXXXXXX,2,Goto(invalidnum,s,1)
+
+; okay, route it
+exten => _1NXXXXXXXXX,2,Goto(pstn-out,${EXTEN:1},1)
+exten => _X.,2,Goto(invalidnum,s,1)
+
+[my-ip]
+exten => s,1,Wait(1)
+	same => n,SayAlpha(${CURL(http://myip.vg)})
+	same => n,Hangup
+
+[allstar-sys]
+exten => _1.,1,Rpt(${EXTEN:1}|Rrpt/node:NODE:rpt/in-call:digits/0:PARKED|120)
+exten => _1.,n,Hangup
+
+exten => _2.,1,Ringing
+exten => _2.,n,Wait(3)
+exten => _2.,n,Answer
+exten => _2.,n,Playback(rpt/node)
+exten => _2.,n,Saydigits(${EXTEN:1})
+exten => _2.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P)
+exten => _2.,n,Hangup
+
+exten => _3.,1,Ringing
+exten => _3.,n,Wait(3)
+exten => _3.,n,Answer
+exten => _3.,n,Playback(rpt/node)
+exten => _3.,n,Saydigits(${EXTEN:1})
+exten => _3.,n,Rpt(${EXTEN:1}|Pv|${CALLERID(name)}-P)
+exten => _3.,n,Hangup
+
+exten => _4.,1,Ringing
+exten => _4.,n,Wait(3)
+exten => _4.,n,Answer
+exten => _4.,n,Playback(rpt/node)
+exten => _4.,n,Saydigits(${EXTEN:1})
+exten => _4.,n,Rpt(${EXTEN:1}|D|${CALLERID(name)}-P)
+exten => _4.,n,Hangup
+
+exten => _5.,1,Ringing
+exten => _5.,n,Wait(3)
+exten => _5.,n,Answer
+exten => _5.,n,Playback(rpt/node)
+exten => _5.,n,Saydigits(${EXTEN:1})
+exten => _5.,n,Rpt(${EXTEN:1}|Dv|${CALLERID(name)}-P)
+exten => _5.,n,Hangup
+
+[allstar-public]
+
+exten => s,1,Ringing
+	same => n,Set(RESP=${CURL(https://register.allstarlink.org/cgi-bin/authwebphone.pl?${CALLERID(name)})})
+	same => n,Set(NODENUM=${CALLERID(number)})
+	same => n,GotoIf($["${RESP:0:1}" = "?"]?hangit)
+	same => n,GotoIf($["${RESP:0:1}" = ""]?hangit)
+	same => n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit)
+	same => n,Set(CALLSIGN=${RESP:5})
+	;exten => s,n,GotoIf($[${DB_EXISTS(whitelist/${CALLSIGN})}]?:hangit)  ; Not in whitelist
+	same => n,Wait(3)
+	same => n,Playback(rpt/node,noanswer)
+	same => n,Saydigits(${NODENUM})
+	same => n,Set(CALLERID(name)=${CALLSIGN})
+	same => n,Set(CALLERID(num)=0)
+	same => n,Rpt(${NODENUM}|X)
+	same => n,Hangup
+	same => n(hangit),Answer
+	same => n,Wait(1)
+	same => n,Hangup
+
+#tryinclude custom/extensions.conf

configs/samples/gps.conf.sample

@@ -0,0 +1,35 @@
+; Configuration for app_gps
+;
+[general]
+; See https://wiki.allstarlink.org/wiki/Gps.conf
+call = W1AW-1               ; callsign (including SSID) for APRS purposes
+password = 12345            ; Password for APRS-IS server for above callsign
+comment = AllStar Node 1999 ; Text to be displayed associated with this station
+server = rotate.aprs2.net   ; APRS-IS server to report information to
+port = 14580                ; port on server to send data
+interval = 600              ; Beacon interval in seconds
+icon = r                    ; A CAR (default) Icon to be displayed for station on APRS display
+comport = /dev/ttyS0        ; Serial port for GPS receiver (specify this only if using GPS receiver)
+baudrate = 4800             ; Baud rate for GPS receiver (specify this only if using GPS receiver)
+debug = n                   ; set this for debug output
+freq = 145.000              ; Display Frequency of station
+tone = 100.0                ; CTCSS tone of station (0.0 for none)
+lat = 12.3456               ; Fixed (default) latitude in decimal degrees
+lon = -123.4567             ; Fixed (default) longitude in decimal degrees
+elev = 123.4                ; Elevation of Antenna in Meters (*NOT* HAAT)
+power = 1                   ; Power level
+height = 2                  ; Antenna Height in HAAT
+gain = 3                    ; Antenna Gain
+dir = 0                     ; Antenna Direction
+
+; ehlert =
+; interval =
+; ttcomment =
+; ttlat =
+; ttlist =
+; ttlon =
+; ttoffset =
+; ttsplit =
+
+#tryinclude custom/gps.conf
+