| layout | title |
|---|---|
documentation |
GE 12725 - ZWave |
{% include base.html %}
This describes the Z-Wave device GE 12725, manufactured by Jasco Products with the thing type UID of ge_12725_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The GE 12725 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
RF controlled, in-wall 1000w dimmer, interchangeable paddle
Press and release the top or bottom of the dimmer smart switch (rocker) to add it in the network.
Press and release the top or bottom of the dimmer smart switch (rocker) to remove it from the network.
The following table summarises the channels available for the GE 12725 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The following table provides a summary of the 9 configuration parameters available in the GE 12725. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | Night Light | Night Light |
| 4 | Invert Switch | Invert Switch |
| 5 | Ignore Start-Level (Receiving) | This dimmer will start dimming from its current level. |
| 7 | On/Off Command Dim Step | On/Off Command Dim Step |
| 8 | On/Off Command Dim Rate | On/Off Command Dim Rate |
| 9 | Local Control Dim Step | Local Control Dim Step |
| 10 | Local Control Dim Rate | Local Control Dim Rate |
| 11 | ALL ON/ALL OFF Dim Step | ALL ON/ALL OFF Dim Step |
| 12 | ALL ON/ALL OFF Dim Rate | ALL ON/ALL OFF Dim Rate |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Night Light Defines the behavior of the blue LED. Default is Night Light mode where LED is on when switch is off. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LED on when switch is OFF |
| 1 | LED on when switch is ON |
| 2 | LED always off |
The manufacturer defined default value is 0 (LED on when switch is OFF).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Invert Switch Invert the ON/OFF Switch State.
Setting this parameter to Yes will change the top of the switch to OFF and the bottom to ON.
Note: If you invert the switches and also install the product upside down, the load will now be control The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No |
| 1 | Yes |
The manufacturer defined default value is 0 (No).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
This dimmer will start dimming from its current level.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No |
| 1 | Yes |
The manufacturer defined default value is 0 (No).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
On/Off Command Dim Step Indicates how many levels the dimmer will change for each dimming step. Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
On/Off Command Dim Rate This value indicates in 10 millisecond resolution This sets how often the dim level will change.
For example, if you set this parameter to 1, then every 10ms the dim level will change.
If you set it to 255, then every 2.55 seconds the dim level will change. Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Local Control Dim Step Indicates how many levels the dimmer will change for each dimming step. Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Local Control Dim Rate This value indicates in 10 millisecond resolution. This sets how often the dim level will change.
For example, if you set this parameter to 1, then every 10ms the dim level will change.
If you set it to 255, then every 2.55 seconds the dim level will change. Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
ALL ON/ALL OFF Dim Step Indicates how many levels the dimmer will change for each dimming step. Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
ALL ON/ALL OFF Dim Rate This value indicates in 10 millisecond resolution. This sets how often the dim level will change.
For example, if you set this parameter to 1, then every 10ms the dim level will change.
If you set it to 255, then every 2.55 seconds the dim level will change. Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The device does not support associations.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.