speaking will also be stuck

[tongjinlv]

When I use stm32f411ce to install the simulator and run arcade uF2 firmware, the sound will be stuck when playing, and adjusting the volume will also be stuck. My definition is as follows

#ifndef BOARD_H
#define BOARD_H

#define OSC_FREQ 25
#define USBDEVICESTRING "Arcade F411"
#define USBMFGSTRING "Contoso Ltd."
#define BOARD_FLASH_SECTORS 8
#define BOARD_FLASH_SIZE (512 * 1024)

#ifdef DEFINE_CONFIGDATA
attribute((section(".config"))) attribute((used)) //
const uint32_t configData[] = {
/* CF2 START /
513675505, 539130489, // magic
29, 100, // used entries, total entries
4, 0x0f, // PIN_BTN_A = PA15
5, 0x14, // PIN_BTN_B = PB04
13, 0x2d, // PIN_LED = PC13
32, 0x05, // PIN_DISPLAY_SCK = PA05
33, 0x06, // PIN_DISPLAY_MISO = PA06
34, 0x07, // PIN_DISPLAY_MOSI = PA07
35, 0x1c, // PIN_DISPLAY_CS = PB12
36, 0x04, // PIN_DISPLAY_DC = PA04
43, 0x01, // PIN_DISPLAY_RST = PA01
44, 0x11, // PIN_DISPLAY_BL = PB01
49, 0x03, // PIN_BTN_LEFT = PA03
50, 0x18, // PIN_BTN_RIGHT = PB08
47, 0x16, // PIN_BTN_UP = PB06
48, 0x19, // PIN_BTN_DOWN = PB9
51, 0x110000, // PIN_BTN_MENU = PA0
64, 0x1f,// PIN_JACK_PWREN = PB15
65, 0x8, // PIN_JACK_SND = PA08//speak
59, 128, // SPEAKER_VOLUME = 128
26, 0x10, // PIN_SPEAKER_AMP = PB00
// //////////////// For ST7735(160x128)
// 37, 0xa0, // DISPLAY_WIDTH = 160
// 38, 0x80, // DISPLAY_HEIGHT = 128
// 39, 0x020180, // DISPLAY_CFG0 = 0x80 ST7735(160x128 GreenTAB)
// 40, 0x603, // DISPLAY_CFG1 = 0x603
// 41, 0x16, // DISPLAY_CFG2 = 0x16
/////////////// For ILI9341(320x240)
37, 320, // DISPLAY_WIDTH = 320
38, 240, // DISPLAY_HEIGHT = 240
39, 0x08, // DISPLAY_CFG0 = 0x08
40, 0x0010ff, // DISPLAY_CFG1 = 0x10ff
41, 50, // DISPLAY_CFG2 = 0x50
78, 9341, // DISPLAY_TYPE = ILI9341
///////////////////////////////////
204, 0x80000, // FLASH_BYTES = 0x80000
205, 0x18000, // RAM_BYTES = 0x18000
208, 0x1f884ff3, // BOOTLOADER_BOARD_ID = 0x1f884ff3
209, 0x57755a57, // UF2_FAMILY = STM32F401
210, 0x10, // PINS_PORT_SIZE = PA_16
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
/ CF2 END */
};
#endif

#endif /* BOARD_H */

[yuanyanhui]

Is this issue related to the bootloader only? Does the sound generation mechanism in the arcade editor also play a part?

[tongjinlv]

When running the utf2 file, it fails when playing audio and when opening the menu to adjust the volume.

[tongjinlv]

It’s okay if you don’t play the audio. If you play the audio, it makes a little sound and then it crashes.

[yuanyanhui]

I am also having the same issue. Just wondering what is the root cause.

[mmoskal]

@yuanyanhui could you post your bootloader config?

@tongjinlv @yuanyanhui which version of arcade are you using? could you share the program you're using to test?

[yuanyanhui]

detected UF2 file

Found CFG DATA at 0x8007c00

PINS_PORT_SIZE = PA_16
PIN_RX = PA10
PIN_TX = PA09
PIN_ACCELEROMETER_INT = PA08
PIN_ACCELEROMETER_SCL = PB06
PIN_ACCELEROMETER_SDA = PB07
PIN_BTN_A = PB05
PIN_BTN_B = PB04
PIN_BTN_DOWN = PB03
PIN_BTN_LEFT = PB01
PIN_BTN_MENU = 0x110000
PIN_BTN_RIGHT = PA15
PIN_BTN_UP = PA06
PIN_DISPLAY_BL = PA03
PIN_DISPLAY_CS = PB12
PIN_DISPLAY_DC = PA04
PIN_DISPLAY_MOSI = PA07
PIN_DISPLAY_RST = PA01
PIN_DISPLAY_SCK = PA05
PIN_LED = PC13
PIN_SPEAKER_AMP = PB00
ACCELEROMETER_TYPE = LIS3DH_ALT
BOOTLOADER_BOARD_ID = 0xc2d0b1e4
BOOTLOADER_PROTECTION = 0
CPU_MHZ = 96
DISPLAY_CFG0 = 0xc0
DISPLAY_CFG1 = 0x603
DISPLAY_CFG2 = 0x16
DISPLAY_HEIGHT = 240
DISPLAY_TYPE = ILI9341
DISPLAY_WIDTH = 320
FLASH_BYTES = 0x80000
POWER_DEEPSLEEP_TIMEOUT = 120
RAM_BYTES = 0x20000
UF2_FAMILY = STM32F401

I use the online editor.
arcade version: 1.2.10
Microsoft MakeCode version: 6.2.23

[tongjinlv]

@yuanyanhui could you post your bootloader config?

@tongjinlv @yuanyanhui which version of arcade are you using? could you share the program you're using to test?

please help me. this is my source https://github.com/tongjinlv/uf2-stm32f

[tongjinlv]

Hello, our problem has not been solved. The chip used is STM32F411CEU6