Skip to content

Latest commit

 

History

History
103 lines (70 loc) · 6.08 KB

README.md

File metadata and controls

103 lines (70 loc) · 6.08 KB
Raw

Spindle plugins

This plugin adds support for some VFD spindles via ModBus (RS485) and a spindle selection plugin.

VFD spindles

VFD spindle support is enabled in my_machine.h by uncommenting \\#define VFD_SPINDLE and changing the VFD spindle number to the desired type or -1 for all.
A list of supported VFDs and associated spindle numbers can be found here.

If all spindles or dual spindle is enabled the active spindle is configured by setting $395.
Note that the setting value not the same as the VFD spindle number used in my_machine.h, either use a sender that supports grblHAL setting enumerations for configuration or output a list with the $$=395 command to find the correct setting value.

If a single VFD spindle is added to the firmware its ModBus address is configured by setting $360 (default 1).
If more than one then the ModBus address is set by one of the following settings depending on the spindle number it is assigned to:

$476 - ModBus address of VFD bound to spindle 0, default 1. Available when spindle 0 is configured as a VFD spindle by $395.
$477 - ModBus address of VFD bound to spindle 1, default 2. Available when spindle 1 is configured as a VFD spindle by $511.
$478 - ModBus address of VFD bound to spindle 2, default 3. Available when spindle 2 is configured as a VFD spindle by $512.
$479 - ModBus address of VFD bound to spindle 4, default 4. Available when spindle 3 is configured as a VFD spindle by $513.

GS20 and YL-620

Setting $461 can be used to set the RPM to HZ relationship. Default value is 60.

MODVFD

The MODVFD spindle uses different register values for the control and RPM functions. The functionality is similar to the VFDMODcomponent from LinuxCNC. The following settings are available:

$462 - Register for Run/stop, default value is 8192.
$463 - Set Frequency Register, default value is 8193.
$464 - Get Frequency Register, default value is 8451.
$465 - Command word for CW, default value is 18.
$466 - Command word for CCW, default value is 34.
$467 - Command word for stop, default value is 1.
$468 - RPM value multiplier for programming RPM, default value is 50.
$469 - RPM value divider for programming RPM, default value is 60.
$470 - RPM value multiplier for reading RPM, default value is 60.
$471 - RPM value divider for reading RPM, default value is 100.

NOTE: settings for ModBus addresses requires a hard reset after changing spindle binding settings (see below) before becoming available.

Additional spindles

Additional spindles may be added by plugin code. If of a generic kind they might be added to this repo based on a pull request.

Spindle selection

grblHAL can operate in three different spindle modes depending on compile time configuration:

  • Only a single spindle is allowed.
    None of the settings or the M-code documented below is available.

  • Up to 321 spindles can be added but only one of up to four1 can be active at a time. Spindle switching is by tool number (see below) or M104:
    Use M104P0 and M104P1 to set the active spindle as spindle number 0 or 1 respectively.
    Use M104Q<n> where <n> is the spindle number to set as the active spindle.

  • Up to 32 spindles can be added and up to four can be active at a time.
    The spindle to control is adressed by the $ gcode word followed by the spindle number, available for the S, M3, M4, M5, M51, G33, G76, G96 and G97 gcode commands.
    Spindle switching by tool number or M104 is not available in this mode.
    NOTE: This mode is work in progress and functionality is not yet complete!

The spindles are dynamically assigned a spindle id at registration, starting from 0. $-settings are then used to tell grblHAL which are to be enabled, by spindle number.

$395 - bind spindle number 0 to the given spindle id. This setting is available when two or more spindles are added.
$511 - bind spindle number 1 to the given spindle id. This setting is available when two or more spindles are added.
$512 - bind spindle number 2 to the given spindle id. This setting is available when three or more spindles are added.
$513 - bind spindle number 3 to the given spindle id. This setting is available when four or more spindles are added.

Available spindles with spindle id, and spindle number if bound, can be listed by the $spindles command. $$=<n> where <n> is a setting number above can be used for listing allowed values.

NOTES: $395 defaults to spindle id 0, this is normally the driver provided PWM spindle but can be another spindle if only one spindle can be registered. Spindle 0 cannot be disabled.

If the grblHAL is configured to handle only one active spindle at a time then $-settings can be used to assign a range of tool numbers to each spindle number. The spindle is then activated on a M6T<n> command where <n> is the tool number.

$520 - lowest tool number for selecting spindle 0, ignored if 0 - normally leave at 0. If set > 0 tool numbers lower than the value will not cause a spindle change.
$521 - lowest tool number for selecting spindle 1, ignored if 0.
$522 - lowest tool number for selecting spindle 2, ignored if 0.
$523 - lowest tool number for selecting spindle 3, ignored if 0.

Tool number vs. spindle is checked from the highest to the lowest spindle number, if all are set to 0 no spindle change takes place.

NOTE: settings for tool number assignments requires a hard reset after changing spindle enable settings before becoming available.
NOTE: when switching between spindles any offset between the spindles must be handled by gcode commands, typically by applying an offset and moving the controlled point (tooltip) to the required position.

1 These numbers are defined by compile time configuration and can be lower.

NOTE: if laser mode is enabled by the $32 setting it will only be honoured if the current spindle is a PWM spindle capable of laser mode.

2023-02-13