Skip to content

Latest commit

 

History

History
99 lines (69 loc) · 3.29 KB

README.asciidoc

File metadata and controls

99 lines (69 loc) · 3.29 KB
Raw

RP2040 nomagic probe

This firmware uses nomagic probe. It provides a gdb server interface to be used with RP2040 (The chip on the RaspberryPi pico board) over a SWD connection.

documentation

please refer to the nomagic probe project for most of the documentation.

Additional documentation can be created by doing

make doc

the created documentation is then located in the build/doxygen/ folder.

building and starting

The firmware can be build using make. The generated Files will be placed in the bin folder. For details try

make help

for this to work you (obviously) need to have make installed. Depending on the target you are building for you might need to have additionaltools installed:

  • To build for ARM Cortex-M Targets you need GCC ARM Embedded

  • to flash and program you need OpenOCD

  • to create an *.uf2 file you need elf2uf2

  • for automatic generated documentation you need Doxygen

pinout

pico

The pico has 40 pins (1..40) Numbered counter clock wise starting at the USB connector.

                  +-----+
           +-------+ USB +---------+
   GPIO 0 -+- 1    +-----+     40 -+- Vbus
   GPIO 1 -+- 2                39 -+- Vsys
      Gnd -+- 3                38 -+- Gnd
   GPIO 2 -+- 4                37 -+- 3V3_EN
   GPIO 3 -+- 5                36 -+- 3V3(Out)
   GPIO 4 -+- 6                35 -+- ADC-Vref
   GPIO 5 -+- 7                34 -+- GPIO 28
      Gnd -+- 8                33 -+- Gnd
   GPIO 6 -+- 9                32 -+- GPIO 27
   GPIO 7 -+- 10               31 -+- GPIO 26
   GPIO 8 -+- 11               30 -+- Run = /Reset
   GPIO 9 -+- 12               29 -+- GPIO 22
      Gnd -+- 13               28 -+- Gnd
  GPIO 10 -+- 14               27 -+- GPIO 21
  GPIO 11 -+- 15               26 -+- GPIO 20
  GPIO 12 -+- 16               25 -+- GPIO 19
  GPIO 13 -+- 17               24 -+- GPIO 18
      Gnd -+- 18               23 -+- Gnd
  GPIO 14 -+- 19               22 -+- GPIO 17
  GPIO 15 -+- 20     Debug     21 -+- GPIO 16
           +-----------------------+
                   S  G  S
                   W  n  W
                   C  d  D
                   L     I
                   K     O

Pin 2: (GPIO 1) SWDIR (High = from Probe to target; Low= from Target to probe)

Pin 4: (GPIO 2) SWCLK

Pin 5: (GPIO 3) SWDIO

Pin 6: (GPIO 4) Target Uart TX (UART1) - output from PC - connect to target RX

Pin 7: (GPIO 5) Target Uart RX (UART1) - input to PC - connect to target TX

Pin 9: (GPIO 6) Run = /Reset

Pin 21: (GPIO 16) Debug Uart TX (UART0)

Pin 22: (GPIO 17) Debug Uart RX (UART0)

license

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License version 2 as published by the Free Software Foundation.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, see http://www.gnu.org/licenses/